E, 0, 2
The machine is out of paper / Paper does not feed
E, 0, 3
Paper Output Tray is closed / Paper jam
E, 0, 4 / E, 0, 5
The FINE Cartridge cannot be recognized
E, 0, 7
FINE Cartridge is not installed in the correct position
E, 0, 8
Ink absorber is almost full
E, 0, 9 (MP270 series only)
The machine has not received a response from the digital camera. The digital camera or digital video camcorder connected is not compatible with this machine.
E, 1, 3
Ink level cannot be detected.
E, 1, 4
The FINE Cartridge cannot be recognized.
E, 1, 5
The FINE Cartridge cannot be recognized.
E, 1, 6
Ink has run out.
E, 1, 9 (MP270 series only)
PictBridge compliant device is connected via a USB hub.
E, 3, 0
The size of the original cannot be correctly detected or the document is too small when the Fit-to-Page copying is selected.
E, 3, 1
The machine is not connected with the computer.
E, 5, 0
Scanning the print head alignment sheet has failed.
P, 0, 2
P, *, *
E, 0, 2
Reload the paper on the Rear Tray correctly and press the Black or Color button.
Loading Paper
See[Loading Paper ]
E, 0, 3
If the Paper Output Tray is closed, open it. The machine resumes printing.
If opening the Paper Output Tray does not resolve the problem, or if the tray was open to begin with, the paper may be jammed. Remove the jammed paper, reload paper properly in the printer, then press the Black or Color button.
Paper Jams
See[Paper Jams]
E, 0, 4 / E, 0, 5
The FINE Cartridge may not be installed properly, or the Cartridge may not be compatible with this machine.
Open the Scanning Unit (Cover) and install the appropriate FINE Cartridge.
If the error is not resolved, contact the service center.
E, 0, 7
Make sure that each FINE Cartridge is installed in the correct position.
Replacing FINE Cartridges
When FINE Cartridges run out of ink, follow the procedure below to replace them.
See[Replacing FINE Cartridges]
E, 0, 8
Press the machine's Black or Color button to continue printing. Contact the service center.
E, 0, 9 (MP270 series only)
Check the device connected to the machine. Printing photos directly is possible only with a PictBridge compliant device.
A communication time out occurs if an operation takes too long or if it takes too much time to send data. This may cancel printing. In such cases, disconnect and reconnect the USB cable.When printing from a PictBridge compliant device, depending on the model or brand of your device, you may have to select a PictBridge compliant print mode on the device before connecting it to the machine. You may also have to turn on your device or select Play mode manually after connecting the device to the machine. Perform necessary operations before connecting your device referring to its instruction manual.If the error is still not resolved, check if you can print another photograph.
E, 1, 3
Ink may have run out.
The function for detecting the remaining ink level will be disabled since the ink level cannot be correctly detected.
If you want to continue printing without this function, press the machine's Stop (Reset) button for at least 5 seconds.
Canon recommends to use new genuine Canon cartridges in order to obtain optimum qualities.
Please be advised that Canon shall not be liable for any malfunction or trouble caused by continuation of printing under the ink out condition.
Checking the Ink Status
You can check the ink status with the Ink lamps on the Operation Panel or with the computer screen.
See[Checking the Ink Status]
E, 1, 4
The FINE Cartridge may not be compatible with this machine.
Install the appropriate FINE Cartridge.
Replacing FINE Cartridges
When FINE Cartridges run out of ink, follow the procedure below to replace them.
See[Replacing FINE Cartridges]
E, 1, 5
The FINE Cartridge may not be installed properly.
Open the Scanning Unit (Cover) and install the FINE Cartridge properly.
Replacing FINE Cartridges
When FINE Cartridges run out of ink, follow the procedure below to replace them.
See[Replacing FINE Cartridges]
E, 1, 6
Ink has run out.
Replace the ink cartridge and close the Scanning Unit (Cover).
If printing is in progress and you want to continue printing, press the machine's Stop (Reset) button for at least 5 seconds with the ink cartridge installed. Then printing can continue under the ink out condition.
The function for detecting the remaining ink level will be disabled.
Replace the empty ink cartridge immediately after the printing. The resulting print quality is not satisfactory, if printing is continued under the ink out condition.
Replacing FINE Cartridges
When FINE Cartridges run out of ink, follow the procedure below to replace them.
See[Replacing FINE Cartridges]
E, 1, 9 (MP270 series only)
If a PictBridge compliant device is connected via a USB hub, remove the hub and connect it directly to the machine.
E, 3, 0
Make sure that the original meets the requirements and is correctly loaded on the Platen Glass.
Check the position and direction of the original loaded on the Platen Glass.
E, 3, 1
Connect the machine and the computer with a USB cable.
E, 5, 0
Press the Stop/Reset button to dismiss the error, then take the actions described below.
Make sure that the print head alignment sheet is set in the correct position and orientation on the Platen Glass.
Make sure the Platen Glass and the print head alignment sheet are not dirty.
Make sure the type and size of loaded paper is suitable for Automatic Print Head Alignment.For Automatic Print Head Alignment, always load one sheet of A4 or letter-sized plain paper.
Make sure if Print Head nozzles are clogged.Print the nozzle check pattern to check the status of the Print Head.
->Printing the Nozzle Check Pattern
If the error is not resolved, connect the machine to the computer and align the Print Head on the printer driver.
Aligning the Print Head
If printed ruled lines are misaligned or print results are otherwise unsatisfactory, adjust the print head position.
See[Aligning the Print Head]
P, 0, 2
Cancel printing, turn off the machine. Then clear the jammed paper or protective material that is preventing the FINE Cartridge Holder from moving, and turn on the machine again.
NOTE
When protective materials are not removed yet,please follow the procedures below.
1. Open the Paper Output Tray.
2. Lift the Scanning Unit (Cover) and fix it with the Scanning Unit Support.
3. Pull the orange protective tape (D) and remove the protective material (E).
4. Lift the Scanning Unit (Cover) slightly and fold the Scanning Unit Support, then gently close the Scanning Unit (Cover).
IMPORTANT
Be careful not to touch the components inside the machine. The machine may not print out properly if you touch it.
If the problem is not resolved, contact the service center.
P, *, *
"*, *" depends on the error occurred.
"P, 1, 0" is displayed:
Turn off the machine, and unplug the power cord of the machine from the power supply.Contact the service center.
"P, 0, 3" is displayed:
If any object is placed in front of the machine, remove it.Open the Paper Output Tray gently, then turn the power off and back on.
In other cases:
Turn off the machine, and unplug the power cord of the machine from the power supply.Plug the machine back in and turn the machine back on.If the problem is not resolved, contact the service center.
Tuesday, September 27, 2011
Canon mp258 error codes
. Carriage error P02 An error occurred in the carriage encoder signal.
1) Confirm that no foreign material is in the area where the carriage moves.
2) Clean the timing slit film.
3) Replace the following items:
- Timing slit film
- Carriage unit
- Logic board
- Carriage motor
2. Line feed error P03 An error occurred in the LF encoder signal.
Replace the following items:
- Timing slit disk film
- Logic board
3. ASF cam sensor error P05 This error takes place when feeding paper
from the rear tray after an error occurred in the rear tray cam sensor.
eplace the following items:
- ASF/PE sensor unit
- Drive unit
- Logic board
4. Internal temperature error P06 The internal temperature is not normal.
Replace the following item:
- Logic board
5. Ink absorber full Japan: Others: P07 The ink absorber becomes full.
Replace the ink absorber (ink absorber kit), and reset the ink absorber counter.
6. Print head temperature rise error P08 The print head temperature exceeded the specified value.
Replace the following items:
- Ink cartridge
- Logic board
7. EEPROM error P09 A problem occurred in reading from or writing to the EEPROM.
Replace the following item:
- Logic board
8. VH monitor error P10 The print head voltage is abnormal.
Replace the following items:
- Ink cartridge
- Logic board
9. USB VBUS overcurrent P15 The USB VBUS is overloaded.
Replace the following item:
- Logic board
10.Other hardware error P20
Replace the following item:
- Logic board
11 Scanner error P22 The scanner unit is faulty.
Replace the following items:
- Scanner unit
- Logic board
1) Confirm that no foreign material is in the area where the carriage moves.
2) Clean the timing slit film.
3) Replace the following items:
- Timing slit film
- Carriage unit
- Logic board
- Carriage motor
2. Line feed error P03 An error occurred in the LF encoder signal.
Replace the following items:
- Timing slit disk film
- Logic board
3. ASF cam sensor error P05 This error takes place when feeding paper
from the rear tray after an error occurred in the rear tray cam sensor.
eplace the following items:
- ASF/PE sensor unit
- Drive unit
- Logic board
4. Internal temperature error P06 The internal temperature is not normal.
Replace the following item:
- Logic board
5. Ink absorber full Japan: Others: P07 The ink absorber becomes full.
Replace the ink absorber (ink absorber kit), and reset the ink absorber counter.
6. Print head temperature rise error P08 The print head temperature exceeded the specified value.
Replace the following items:
- Ink cartridge
- Logic board
7. EEPROM error P09 A problem occurred in reading from or writing to the EEPROM.
Replace the following item:
- Logic board
8. VH monitor error P10 The print head voltage is abnormal.
Replace the following items:
- Ink cartridge
- Logic board
9. USB VBUS overcurrent P15 The USB VBUS is overloaded.
Replace the following item:
- Logic board
10.Other hardware error P20
Replace the following item:
- Logic board
11 Scanner error P22 The scanner unit is faulty.
Replace the following items:
- Scanner unit
- Logic board
Monday, September 26, 2011
How do i restore my macbook white os x to factory settings without the disc?
para sa mga my laptop ng MacBook apple or mac os-x, sana po makatulong ako sa inyo....
I have recently purchased a white mac book which appears to be locked as the previous owner didn't tell me the password. I also do not have the os x disc, anyone?
Contact the previous owner and explain that the resore discs than came with this white MacBook are only useful with another white MacBook. He can't use them on a newer Mac, so why is he hording them? He should be fair to you and give you the restore discs. Meanwhile, I hope you now realize that every computer needs a system disc, just as every car needs a spare tire and jack.
Some choices:
If you don't have an OS X install disc...
Method 1: Take the computer to a neighbor who has a Mac, an Apple retail store, or a Mac service shop and ask them to boot it to an OS X DVD and reset the password.
Method 2 (For OS 10.5 -- requires your knowing the short name of the user home folder--first link below):
Oh, wait a second...You don't know the user short name, do you? Then go ahead to...
Method 3 (will delete the previous user account and put all user documents into a disk image):
Boot to single-user mode and:
Type "/sbin/mount -uw /"
Press Return. (Nothing appears to happens, no problem. Also, you will see # again. That's fine; ignore it.)
Type "rm /var/db/.applesetupdone" (The normal format of Mac OS doesn't care about upper case.)
Press Return.
Type "reboot"
Press Return. (Now stuff appears to happen. You will finally get past the "Welcome" in a dozen languages and then you can create a new admin user. A few screens later, you come to the registration. Just choose "later". It doesn't come back later to nag.
After you have completed the new user, open the Users folder and look for "Deleted Users". It will have a mountable disk image that contains all the previous owner's documents. If they are of no use to you, trash them. He kept the system disc, so why return his old documents?
Source(s):
http://www.macosxhints.com/article.php?s…
http://support.apple.com/kb/HT1274
Each modern MacBook comes with the original Mac OS as part of the computer's package. If your MacBook is acting strangely--for example, running slowly or not loading applications properly--you can restore your MacBook to the factory settings to fix it. In some cases, this will repair whatever was going wrong with your computer. However, to totally restore the factory settings on a MacBook, you have to erase all of the files on it and start over.
Difficulty:
Moderately Easy
Instructions
1
Insert your MacBook restore DVD 1 into your computer and restart. Hold down "C" as the computer boots so it will boot from the disk.
2
Select your language and click "Continue."
3
Click "Options" at the "Select a Destination" window.
4
Choose "Erase and Install." Click "Continue."
5
Choose "Basic Install." Click "Install." Once the install is complete, your MacBook will be restored to its factory settings.
Download Cleaner for OS Xmacpaw.com/CleanMyMac
Get your Mac OS running faster with only a few clicks. Download free.
Pro. PVC Raw-Meterialswww.skybright-chemicals.com
China Excellent Manufacturer, Top Quality, Good Price!
The HP Mini Laptopwww.hp.com/ph
Ultra-Lightweight, Sleek & Chic Small In Size, Big In Functionality
HDD Regeneratorwww.dposoft.net
Repair bad sectors on damaged hard drive. Resue data.
Ads by Google
Tips & Warnings
You may have to insert the other restore DVDs as your MacBook asks for them.
Restoring a MacBook to factory settings can take an hour or more.
Be sure to back up all important files on your MacBook to an external drive or DVD before you restore the factory settings.
Read more: How to Restore My Macbook to Factory Setting | eHow.com http://www.ehow.com/how_5926047_restore-macbook-factory-setting.html#ixzz1UUbTcbaG
I have recently purchased a white mac book which appears to be locked as the previous owner didn't tell me the password. I also do not have the os x disc, anyone?
Contact the previous owner and explain that the resore discs than came with this white MacBook are only useful with another white MacBook. He can't use them on a newer Mac, so why is he hording them? He should be fair to you and give you the restore discs. Meanwhile, I hope you now realize that every computer needs a system disc, just as every car needs a spare tire and jack.
Some choices:
If you don't have an OS X install disc...
Method 1: Take the computer to a neighbor who has a Mac, an Apple retail store, or a Mac service shop and ask them to boot it to an OS X DVD and reset the password.
Method 2 (For OS 10.5 -- requires your knowing the short name of the user home folder--first link below):
Oh, wait a second...You don't know the user short name, do you? Then go ahead to...
Method 3 (will delete the previous user account and put all user documents into a disk image):
Boot to single-user mode and:
Type "/sbin/mount -uw /"
Press Return. (Nothing appears to happens, no problem. Also, you will see # again. That's fine; ignore it.)
Type "rm /var/db/.applesetupdone" (The normal format of Mac OS doesn't care about upper case.)
Press Return.
Type "reboot"
Press Return. (Now stuff appears to happen. You will finally get past the "Welcome" in a dozen languages and then you can create a new admin user. A few screens later, you come to the registration. Just choose "later". It doesn't come back later to nag.
After you have completed the new user, open the Users folder and look for "Deleted Users". It will have a mountable disk image that contains all the previous owner's documents. If they are of no use to you, trash them. He kept the system disc, so why return his old documents?
Source(s):
http://www.macosxhints.com/article.php?s…
http://support.apple.com/kb/HT1274
Each modern MacBook comes with the original Mac OS as part of the computer's package. If your MacBook is acting strangely--for example, running slowly or not loading applications properly--you can restore your MacBook to the factory settings to fix it. In some cases, this will repair whatever was going wrong with your computer. However, to totally restore the factory settings on a MacBook, you have to erase all of the files on it and start over.
Difficulty:
Moderately Easy
Instructions
1
Insert your MacBook restore DVD 1 into your computer and restart. Hold down "C" as the computer boots so it will boot from the disk.
2
Select your language and click "Continue."
3
Click "Options" at the "Select a Destination" window.
4
Choose "Erase and Install." Click "Continue."
5
Choose "Basic Install." Click "Install." Once the install is complete, your MacBook will be restored to its factory settings.
Download Cleaner for OS Xmacpaw.com/CleanMyMac
Get your Mac OS running faster with only a few clicks. Download free.
Pro. PVC Raw-Meterialswww.skybright-chemicals.com
China Excellent Manufacturer, Top Quality, Good Price!
The HP Mini Laptopwww.hp.com/ph
Ultra-Lightweight, Sleek & Chic Small In Size, Big In Functionality
HDD Regeneratorwww.dposoft.net
Repair bad sectors on damaged hard drive. Resue data.
Ads by Google
Tips & Warnings
You may have to insert the other restore DVDs as your MacBook asks for them.
Restoring a MacBook to factory settings can take an hour or more.
Be sure to back up all important files on your MacBook to an external drive or DVD before you restore the factory settings.
Read more: How to Restore My Macbook to Factory Setting | eHow.com http://www.ehow.com/how_5926047_restore-macbook-factory-setting.html#ixzz1UUbTcbaG
Mac OS X v10.6 Snow Leopard: How to Erase and Install
i-share ko lang po ito para sa mga my MAC OS-X kung paano mu clean install ang laptop mu sana po makatulog pls click my ads ty...
Summary
Use these steps to restore to the factory settings and the software that originally came with your computer by using the installation DVDs that shipped with it. Important: For MacBook Air, a MacBook Air SuperDrive, or MacBook Air Software Reinstall Drive is required to complete this procedure.
Products Affected
iMac (21.5-inch, Late 2009), Mac OS X 10.6, Mac mini (Late 2009), MacBook Air (11-inch, Late 2010), iMac (27-inch, Late 2009), MacBook Air (13-inch, Late 2010), MacBook (13-inch, Late 2009)
This procedure has four parts:
Erasing the hard drive
Restoring the Mac OS X operating system using the Mac OS X Install DVD.
Completing the Mac OS X Setup Assistant.
Restoring the bundled applications using the Applications Install Disc.
Important: This procedure will completely erase your hard drive. If you have installed Microsoft Windows using Boot Camp, or have multiple partitions, this procedure will erase the partition you select.
Part One: Erasing the hard drive
Turn on the computer.
Insert the Mac OS X Install DVD into the optical drive, or insert the MacBook Air Software Reinstall Drive into the USB port.
Press and hold the "C" key while the computer starts up. The computer will start up using the Install media. Alternatively, press and hold the Option key at startup to select the volume containing the installer.
If your are using a wireless mouse, a mouse icon should appear asking you to turn the mouse on so that the computer can discover it.
Select a language, then press the right arrow key.
Click the Utilities menu, the choose Disk Utility.
Select a volume to erase (usually called Macintosh HD).
Click the Erase tab.
Click Erase... Important: This step will completely erase your hard drive. If you have installed Microsoft Windows using Boot Camp, or have multiple partitions, this procedure will erase the partition you select.
A dialog box appears asking if you want to erase the partition: click Erase.
After the partition is erased, choose Quit Disk Utility from the Disk Utility menu.
Part Two: Installing the operating system
When the Mac OS X Snow Leopard Installer screen appears, click Continue.
When the license agreement appears, click Agree.
Select the disk you erased. It should now be highlighted with a green arrow.
Click Install. A status bar appears on the bottom of the screen while Mac OS X installs.
An Additional Information screen appears, advising you that you operating system has been installed. Click Continue.
An Install Succeeded screen appears. Click Restart.
Part Three: Completing the Mac OS X Setup Assistant
When the restart has completed, a welcome video plays, then country/region selection screen appears.
Select your country or region and click Continue.
Select a keyboard layout and click Continue.
A migration screen appears. If you wish to migrate your data from another Macintosh, see Migration tips and tricks. If you do not wish to migrate, or want to migrate later, select "Do not transfer my information now" and click Continue.
A Wireless Service screen appears if you have wireless services available within range of your computer. Select "On" and click Continue.
If the network is password protected, you be asked for a password when you select it. Type the password and click Continue.
An Apple ID screen appears. This is used to purchase content from the iTunes store. You can use MobileMe or .Mac usernames here as well. When complete, click Continue.
If you do not have an Apple ID or MobileMe account, click Continue to move to the next screen.
A Registration Information screen appears. You are not required to fill this out, but it is helpful if you do. When complete, click Continue and your product registration will be sent immediately.
If Mac OS X servers are available on your network, you'll be asked if you'd like to log on to them. If not, click Continue.
A Create Your Account screen appears. This will be used to create a User Account with Login ID and Password for you computer. You should remember this password. You'll be asked for it when you install new software or perform other administrative tasks on your computer. When complete, click Continue and your account will be created immediately.
A screen to select your user picture appears. Take a snapshot with the built-in camera or select a picture from your Library. When complete, click Continue.
A MobileMe screen appears. Select an option and click Continue.
A Thank You screen appears. Click Go to complete the Mac OS X Setup Assistant.
Eject the Mac OS X Install DVD by dragging its icon to the Trash.
Part Four: Installing the bundled applications
To install the bundled applications, locate the Applications Install Disc or MacBook Air Software Reinstall Drive that came with your computer.
Note: You may see a Software Update icon bouncing up and down in your dock. You can quit this for now.
Insert the Applications Install Disc into the optical drive, or insert the MacBook Air Software Reinstall Drive into the USB port.
The disc will mount and an Applications Install Disk dialog appears. Double-click on Install Bundled Software to install your iLife applications. If you are using the MacBook Air Software Reinstall Drive, double-click the Install iLife icon.
A dialog appears asking if you want to run the package. Click Continue.
The Bundled Software Applications Installer screen appears. Click Continue.
A software license screen appears. Click Continue, then click Agree to accept the terms.
A select destination dialog appears. Make sure the partition with the green arrow is the correct destination, then click Continue.
To install all the bundled applications, click Install.
To select individual applications, click Customize. Click the disclosure triangle next to Bundled Applications to select individual applications, then click Install. Clicking Standard Install on the Customize screen installs all the applications.
Type the password you created in Part Three, step 11 to start the installation.
A restart dialog appears. Click Continue Installation.
An Install was Successful screen appears. Click Restart.
The restore process is now complete.
It is a good idea to make sure you've updated all the software after performing this procedure. From the Apple () menu, choose Software Update to find the updates currently available for your computer.
Summary
Use these steps to restore to the factory settings and the software that originally came with your computer by using the installation DVDs that shipped with it. Important: For MacBook Air, a MacBook Air SuperDrive, or MacBook Air Software Reinstall Drive is required to complete this procedure.
Products Affected
iMac (21.5-inch, Late 2009), Mac OS X 10.6, Mac mini (Late 2009), MacBook Air (11-inch, Late 2010), iMac (27-inch, Late 2009), MacBook Air (13-inch, Late 2010), MacBook (13-inch, Late 2009)
This procedure has four parts:
Erasing the hard drive
Restoring the Mac OS X operating system using the Mac OS X Install DVD.
Completing the Mac OS X Setup Assistant.
Restoring the bundled applications using the Applications Install Disc.
Important: This procedure will completely erase your hard drive. If you have installed Microsoft Windows using Boot Camp, or have multiple partitions, this procedure will erase the partition you select.
Part One: Erasing the hard drive
Turn on the computer.
Insert the Mac OS X Install DVD into the optical drive, or insert the MacBook Air Software Reinstall Drive into the USB port.
Press and hold the "C" key while the computer starts up. The computer will start up using the Install media. Alternatively, press and hold the Option key at startup to select the volume containing the installer.
If your are using a wireless mouse, a mouse icon should appear asking you to turn the mouse on so that the computer can discover it.
Select a language, then press the right arrow key.
Click the Utilities menu, the choose Disk Utility.
Select a volume to erase (usually called Macintosh HD).
Click the Erase tab.
Click Erase... Important: This step will completely erase your hard drive. If you have installed Microsoft Windows using Boot Camp, or have multiple partitions, this procedure will erase the partition you select.
A dialog box appears asking if you want to erase the partition: click Erase.
After the partition is erased, choose Quit Disk Utility from the Disk Utility menu.
Part Two: Installing the operating system
When the Mac OS X Snow Leopard Installer screen appears, click Continue.
When the license agreement appears, click Agree.
Select the disk you erased. It should now be highlighted with a green arrow.
Click Install. A status bar appears on the bottom of the screen while Mac OS X installs.
An Additional Information screen appears, advising you that you operating system has been installed. Click Continue.
An Install Succeeded screen appears. Click Restart.
Part Three: Completing the Mac OS X Setup Assistant
When the restart has completed, a welcome video plays, then country/region selection screen appears.
Select your country or region and click Continue.
Select a keyboard layout and click Continue.
A migration screen appears. If you wish to migrate your data from another Macintosh, see Migration tips and tricks. If you do not wish to migrate, or want to migrate later, select "Do not transfer my information now" and click Continue.
A Wireless Service screen appears if you have wireless services available within range of your computer. Select "On" and click Continue.
If the network is password protected, you be asked for a password when you select it. Type the password and click Continue.
An Apple ID screen appears. This is used to purchase content from the iTunes store. You can use MobileMe or .Mac usernames here as well. When complete, click Continue.
If you do not have an Apple ID or MobileMe account, click Continue to move to the next screen.
A Registration Information screen appears. You are not required to fill this out, but it is helpful if you do. When complete, click Continue and your product registration will be sent immediately.
If Mac OS X servers are available on your network, you'll be asked if you'd like to log on to them. If not, click Continue.
A Create Your Account screen appears. This will be used to create a User Account with Login ID and Password for you computer. You should remember this password. You'll be asked for it when you install new software or perform other administrative tasks on your computer. When complete, click Continue and your account will be created immediately.
A screen to select your user picture appears. Take a snapshot with the built-in camera or select a picture from your Library. When complete, click Continue.
A MobileMe screen appears. Select an option and click Continue.
A Thank You screen appears. Click Go to complete the Mac OS X Setup Assistant.
Eject the Mac OS X Install DVD by dragging its icon to the Trash.
Part Four: Installing the bundled applications
To install the bundled applications, locate the Applications Install Disc or MacBook Air Software Reinstall Drive that came with your computer.
Note: You may see a Software Update icon bouncing up and down in your dock. You can quit this for now.
Insert the Applications Install Disc into the optical drive, or insert the MacBook Air Software Reinstall Drive into the USB port.
The disc will mount and an Applications Install Disk dialog appears. Double-click on Install Bundled Software to install your iLife applications. If you are using the MacBook Air Software Reinstall Drive, double-click the Install iLife icon.
A dialog appears asking if you want to run the package. Click Continue.
The Bundled Software Applications Installer screen appears. Click Continue.
A software license screen appears. Click Continue, then click Agree to accept the terms.
A select destination dialog appears. Make sure the partition with the green arrow is the correct destination, then click Continue.
To install all the bundled applications, click Install.
To select individual applications, click Customize. Click the disclosure triangle next to Bundled Applications to select individual applications, then click Install. Clicking Standard Install on the Customize screen installs all the applications.
Type the password you created in Part Three, step 11 to start the installation.
A restart dialog appears. Click Continue Installation.
An Install was Successful screen appears. Click Restart.
The restore process is now complete.
It is a good idea to make sure you've updated all the software after performing this procedure. From the Apple () menu, choose Software Update to find the updates currently available for your computer.
Satellite L310,Satellite M300,Satellite Pro M300
Para sa mga my Laptop ng Toshiba Satellite L310 Driver for Windows 7 & Windows Vista
Upgrade Your TOSHIBA PC Notebook to Windows® 7
Update Your Drivers for Windows® 7
Drivers List for Your PC
Satellite L310,Satellite M300,Satellite Pro M300
32bit / 64bit
OS Category Component Download
On Vista
Driver
TOSHIBA HDD Protection
Download
On Vista
Driver
Truesuite Access Manager uninstaller
Download
On Vista
Utility
Bluetooth Stack for Windows by Toshiba
Download
On Vista
Utility
Intel ProSet
-
Windows7
TVAP
TOSHIBA Value Added Package
Download
Windows7
Driver
Atheros Wireless LAN Driver
Download
Windows7
Driver
Atheros Wireless LAN Driver
-
Windows7
Driver
Authentec Fingerprint Driver
Download
Windows7
Driver
Chicony Camera Assistant Software
Download
Windows7
Driver
Conexant Audio Driver
Download
Windows7
Driver
Intel Chipset SW Installation Utility
Download
Windows7
Driver
Intel Display Driver
Download
Windows7
Driver
Intel Matrix Storage Manager
Download
Windows7
Driver
Marvell LAN Driver
Download
Windows7
Driver
O2 Card Reader Controller
Download
Windows7
Driver
PatchFiles(TOSHIBA Storage Configuration Patch for Windows7)
Download
Windows7
Driver
Realtek Wireless LAN Driver
Download
Windows7
Driver
TOSHIBA Registry Patch for Windows7 Devices & Printers
Download
Windows7
Driver
Winbond CIR Driver
Download
Windows7
Utility
ConfigFree
Download
Windows7
Utility
HDMI Control Manager
Download
Windows7
Application
TOSHIBA Disc Creator
Download
Windows7
Application
TOSHIBA DVD PLAYER
Download
Windows7
Application
TOSHIBA Speech System
Download
Windows7
Utility
TOSHIBA HW Setup Utility
Download
Windows7
Utility
TOSHIBA Supervisor Password Utility
Download
Driver
ALPS Pointing Device Driver
-
Driver
Conexant Modem Driver
-
Driver
NXP FM Tuner Driver
-
Driver
Synaptics Touch Pad Driver
-
Utility
CD/DVD Drive Acoustic Silencer
-
Utility
Sun Java 2 Runtime Environment
-
Utility
TOSHIBA Extended Tiles for Windows Mobility Center
-
Utility
TOSHIBA Face Recognition
-
Utility
TOSHIBA Recovery Disc Creator
-
Utility
TOSHIBA Recovery Disc Creator Launcher
-
Utility
TOSHIBA Remote Control Manager
-
Application
Bluetooth Monitor
-
Application
Presto! BizCard 5
-
Application
Ulead DVD Movie Writer for TOSHIBA (V5.51)
-
Driver
Intel Wireless LAN Driver
-
Driver
Intel Wireless LAN Driver
-
Driver
TOSHIBA TRS Driver
-
Providing the Latest Software and Drivers
After upgrading to Windows 7, the latest driver and software updates will be provided via Toshiba Service Station. We recommend you to use the Toshiba Service Station to maintain your system up-to-date.
Upgrade Your TOSHIBA PC Notebook to Windows® 7
Update Your Drivers for Windows® 7
Drivers List for Your PC
Satellite L310,Satellite M300,Satellite Pro M300
32bit / 64bit
OS Category Component Download
On Vista
Driver
TOSHIBA HDD Protection
Download
On Vista
Driver
Truesuite Access Manager uninstaller
Download
On Vista
Utility
Bluetooth Stack for Windows by Toshiba
Download
On Vista
Utility
Intel ProSet
-
Windows7
TVAP
TOSHIBA Value Added Package
Download
Windows7
Driver
Atheros Wireless LAN Driver
Download
Windows7
Driver
Atheros Wireless LAN Driver
-
Windows7
Driver
Authentec Fingerprint Driver
Download
Windows7
Driver
Chicony Camera Assistant Software
Download
Windows7
Driver
Conexant Audio Driver
Download
Windows7
Driver
Intel Chipset SW Installation Utility
Download
Windows7
Driver
Intel Display Driver
Download
Windows7
Driver
Intel Matrix Storage Manager
Download
Windows7
Driver
Marvell LAN Driver
Download
Windows7
Driver
O2 Card Reader Controller
Download
Windows7
Driver
PatchFiles(TOSHIBA Storage Configuration Patch for Windows7)
Download
Windows7
Driver
Realtek Wireless LAN Driver
Download
Windows7
Driver
TOSHIBA Registry Patch for Windows7 Devices & Printers
Download
Windows7
Driver
Winbond CIR Driver
Download
Windows7
Utility
ConfigFree
Download
Windows7
Utility
HDMI Control Manager
Download
Windows7
Application
TOSHIBA Disc Creator
Download
Windows7
Application
TOSHIBA DVD PLAYER
Download
Windows7
Application
TOSHIBA Speech System
Download
Windows7
Utility
TOSHIBA HW Setup Utility
Download
Windows7
Utility
TOSHIBA Supervisor Password Utility
Download
Driver
ALPS Pointing Device Driver
-
Driver
Conexant Modem Driver
-
Driver
NXP FM Tuner Driver
-
Driver
Synaptics Touch Pad Driver
-
Utility
CD/DVD Drive Acoustic Silencer
-
Utility
Sun Java 2 Runtime Environment
-
Utility
TOSHIBA Extended Tiles for Windows Mobility Center
-
Utility
TOSHIBA Face Recognition
-
Utility
TOSHIBA Recovery Disc Creator
-
Utility
TOSHIBA Recovery Disc Creator Launcher
-
Utility
TOSHIBA Remote Control Manager
-
Application
Bluetooth Monitor
-
Application
Presto! BizCard 5
-
Application
Ulead DVD Movie Writer for TOSHIBA (V5.51)
-
Driver
Intel Wireless LAN Driver
-
Driver
Intel Wireless LAN Driver
-
Driver
TOSHIBA TRS Driver
-
Providing the Latest Software and Drivers
After upgrading to Windows 7, the latest driver and software updates will be provided via Toshiba Service Station. We recommend you to use the Toshiba Service Station to maintain your system up-to-date.
Hide User Accounts on Windows 7 Logon
Hide User Accounts on Windows 7 Logon
Hi, gusto ko ibahagi sa inyo ito 100%working po ito sana po makatulong...
hit my google ads ty.....
you can do this through secpol.msc
1. Klick Start->Run->secpol.msc
2. Navigate to Local policies -> Security settings
3. Find the entry "Interactive Logon: Hide last user..." and set it to activated.
4. Reboot the machine
Tto hide additional user accounts on Windows & Logon Use Regedit, also works for Vista
Hide User Accounts in windows Vista and Windows 7
at Run type regedit
Once in regedit go to HKEY_LOCAL_MACHINE\Software\Microsoft\WindowsNT\CurrentVersion\Winlogon
In the left panel, right click on Winlogon and click New and click Key.
Type SpecialAccounts and press Enter
In the left panel, right click on SpecialAccounts and click New and click Key.
Type UserList and press Enter.
In right panel of UserList, right click on a empty area and click New then click DWORD (32bit) Value.
Type in the name of the user account that you want to hide and press Enter.eg: Everyday Account.
In the right panel, right click on the user account name and click Modify.
To hide the user account – Type 0 and click OK. (number zero not the letter)
Whenever you want to use the account just unhide the it by typing 1 instead of zero.
It only takes less than 5 seconds to click my ADS by GOOGLE! Don't be a LEECHER!!!
Hi, gusto ko ibahagi sa inyo ito 100%working po ito sana po makatulong...
hit my google ads ty.....
you can do this through secpol.msc
1. Klick Start->Run->secpol.msc
2. Navigate to Local policies -> Security settings
3. Find the entry "Interactive Logon: Hide last user..." and set it to activated.
4. Reboot the machine
Tto hide additional user accounts on Windows & Logon Use Regedit, also works for Vista
Hide User Accounts in windows Vista and Windows 7
at Run type regedit
Once in regedit go to HKEY_LOCAL_MACHINE\Software\Microsoft\WindowsNT\CurrentVersion\Winlogon
In the left panel, right click on Winlogon and click New and click Key.
Type SpecialAccounts and press Enter
In the left panel, right click on SpecialAccounts and click New and click Key.
Type UserList and press Enter.
In right panel of UserList, right click on a empty area and click New then click DWORD (32bit) Value.
Type in the name of the user account that you want to hide and press Enter.eg: Everyday Account.
In the right panel, right click on the user account name and click Modify.
To hide the user account – Type 0 and click OK. (number zero not the letter)
Whenever you want to use the account just unhide the it by typing 1 instead of zero.
It only takes less than 5 seconds to click my ADS by GOOGLE! Don't be a LEECHER!!!
Subscribe to:
Posts (Atom)